Beninca Brain 24 Manual. Instruction Manual for Beninca Brain 24 Control Panel. Copy to Email · Send to Mobile. Print. Download · Buy Product. Name. 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 8k2 Command central for 1/2 24Vdc motor, for single or sliding doors: BRAINY Beninca Brain 24 – EasyGates Manuals & Guides. L Rev. 02/06/02 CENTRALE DI COMANDO CONTROL UNIT STEUEREINHEIT CENTRALE DE.
|Published (Last):||22 October 2014|
|PDF File Size:||4.58 Mb|
|ePub File Size:||7.55 Mb|
|Price:||Free* [*Free Regsitration Required]|
If buffer batteries are used, connect the CB. OFFas the end of operation is determined 11 only by the triggering of the limit switch or by the amperometric sensor. Active only with TCA: Control Unit Beninca CP.
The amperometric sensor activation is interpreted by the control unit as limit benlnca. Receiver enabled for rolling-code and programmable code transmitters self-learning and Dip Switch. Add to my manuals Add. SCA contact, open gate indicator. For example, with a 20s stroke, preset 17s to start the braking phase, 3s in advance with respect to end of movement. Returns the control benica to the default values. One segment of the display is linked to each input.
AUTOMATIONS FOR SWINGING GATES
Radio receiver enabled only for rolling-code transmitters. Limit switches not provided. If the battery charger board CB. By pressing ‘print’ button you braij print only current page. Other special functions follow the parameters and logic menus bbrain may vary depending on the type of control unit or the software release. Make sure the devices are correctly connected i. Comply with regulations in force! Page 6 only by the triggering of the limit switch or by the amperometric sensor. With the gate open or in the opening phase the intervention of the photocell causes automatic closing after 3 s.
brin At the end of the set time the control unit orders a closing manoeuvre. After the activation of closure limit switches the control unit delays the stop by approx.
OFF serL Service light function is enabled or disabled on output If the code is valid, it is stored in memory and OK appears. Function Description Motor 1 Connection, motor 1: Regulates the delay time of motor 2 on opening with respect to motor 1 Mot. Example of programming Let us suppose it is necessary to: The operating time is adjusted at normal speed during motor 2 opening bennica closing phases.
The operating time beninac adjusted at normal speed during motor 1 opening and closing phases. CLr By selecting this function, the receiver awaits Push for a transmitter code to be erased from memory. The performance of the output is preset by 2ch parameter, see previous parameter.
With 2ch logic On: The speed of the motor during braking is determined by the SLDS parameter value.
Page 5 The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch. Before each opening manoeuvre the power supply is interrupted for the time set by the parameter TLOC. The amperometric sensor activation is interpreted by the control unit as obstacle present in the gate movement area.
Beninca BRAINY24 24Vdc Control panel for 1 or 2 motors REPLACES BRAIN24
Only motor 1 operating. Got it, continue to print. The speed of the motor during braking is determined by the SLDS parameter value. Receiver enabled for rolling-code and programmable code transmitters self-learning and Dip Switch. If the electric lock is not used, set the parameter at 0.
If 244 code is not valid, the wording Err is displayed. It’s a community-based project which helps to repair anything. Page of 9 Go. Similarly to the safety edge activation, the control signal is sent to stop and reverse movement for approx. The output has the function of 2nd radio channel: Confirmation of operation is required.
Beninca Brain 24 – EasyGates Manuals & Guides |
The operation mode of the amperometric sensor is selected ei- ther the limit switches are provided or not. Contact controlled by 2nd radio channel of the receiver. Comments to this Manuals Your Name.
The step-by-step impulse or transmitter impulse has no effect during the opening phase. Adjustment of braking With braking enabled SLD logic: Don’t show me this message again. The value is expressed in percentage with respect to speed during normal operation.
To use this function, close the limit switch contacts with jumpers. If the code is valid, it is erase and OK appears. OFF Sld Enables or disables slowing.